Abrasive Materials

Sheet for hand sanding on a paper or cloth backing, sandpaper for use on paint with a dust-repellent coating. It is intended for all kinds of manual use and for vibrating format sanders on wood, metal, paint and plastic.

Rolls of abrasives on a paper or cloth backing for hand sanding or for use on a horizontal sander. Paper for paint sanding with a dust-repellent coating. Universal use on metal, wood, paint, plastics, etc.

Belts with a durable cloth backing in various dimensions with a width of up to 1,320 mm. Universal use in working with metal, high-grade steel, wood, plastics and glass. Usable for both wet and dry sanding.

Universally usable sanding belts on a cloth backing for handheld sanders for working with wood, metal, plastics, glass, etc.

Sanding belts on paper backing for belt sanders. Abrasive grains with aluminium oxide or silicon carbide, also available with dust-repellent or anti-static coating. For use in the woodworking industry, sanding paint, flat steel parts, aluminium and plastics.

Wide sanding belts on a paper backing with a width of up to 1400 mm with aluminium oxide or silicon carbide grain for sanding wood and paint. For use in sanding steel on a wide-belt sanders for finish sanding. Also available with an anti-static coating.

Sanding bands are used when working with small diameters in the processing of metal and plastics. For use on on flexible shafts and straight sanders. Various diameters, for use on rubber mandrels with a shank. Special bands are also available for sanding stainless steel.

For use on steel, non-ferrous metals, aluminium, etc. on handheld grinders, bench buffing machines and automated grinding machines. For deburring and finishing work, conforming to the surface. Smaller diameters on a shank are also available.

Self-adhesive discs and strips for surface finishing in the area of plastics, metal, wood sanding and paint sanding. Used primarily on eccentric and orbital sanders. Also available in rolls, with or without holes for dust extraction. Handheld pad with self-adhesive rolls for all manual work.

Sanding discs and strips on hook-and-loop backing, perforated or without holes. These are used primarily on vibrating and orbital sanders. For working with metal, plastics, wood and paint.

Sanding discs with a paper or cloth backing, also self-adhesive. Available in multiples sizes as needed. For use on flat sanders for deburring, edge chamfering and vibration surface sanding of metals, wood and plastics; for use in foundries, construction of models, etc.

For use on angle grinders in working with the broadest range of materials. Special discs for highly alloyed and stainless steel, for working on welds, edges and surfaces.

For use on angle grinders in working with the broadest range of materials. Longer service life than in the case of fibre discs, consistent cut appearance. It is possible to obtain special discs for working with high-grade and stainless steel.

For use on handheld and stationary machines for achieving the final appearance of wood and painted surfaces. Sanding brushes also enable machine sanding of more complex profiles.

Sanding sponges have a broad range of uses for all sanding and cleaning work. They are suitable also for hard-to-reach places, corners and contoured surfaces. Sanding sponges are flexible, with 2-4 sides covered with abrasive grain.

Sanding screens are mostly used as discs on flat disc sanders for sanding parquet floors. They can also be used for finish sanding and cleaning work on metal. When used manually, sanding screens are used for surface cleaning and finishing. The design prevents clogging (accumulation of sanding dust), as the dust falls through the openings in the screen.

Trizact^TM abrasives are intended for forming precise and consistent surfaces. In terms of durability and size, the consistency of the unique pyramidal surface of Trizact^TM structured abrasive materials ensures sanding quality that is so predictable and consistent that it can be accurately measured. In addition to that, Trizact^TM structured abrasive materials enable users to apply less pressure, thus improving their sensitivity and control, which means less fatigue and even greater consistency.

This fibre-fleece material for manual cleaning, deburring and finishing and sanding of metal, wood and plastic surfaces can be used both in production and in home workshops. It is suitable for smoothing painted profiles. No sanding through on stained edges and corners. Deburring of wooden surfaces. Fibre fleece is a replacement for steel wool and conforms to the surface of the workpiece. It is very flexible and can be used for both wet and dry sanding.

Handheld fibre-fleece material for cleaning, deburring and finishing and sanding of surfaces of metal, wood, plastic and other materials in craft production as well as in home workshops. It can also be used on orbital sanders. The material replaces steel wool and conforms to the workpiece surface. It is very flexible and can be used for both wet and dry sanding.

Fibre-fleece discs are durable, reinforced with a cloth or fibre backing. They adhere well to pads equipped with hook-and-loop material and are used primarily on handheld angle grinders. They are particularly suitable for cleaning, final surface finishing and deburring. Scotch-Brite^TM discs available with a fibre backing. An advantage is their longer service life and the possibility of attaching them to common fibre pads used on angle grinders.

Any number of these discs can be combined on one shaft of a stationary grinding or buffing machine in the form of disc brushes or brush cylinders. This configuration can be used advantageously for more complex metal and wood profiles and for finishing surfaces of plastics such as Corian, Avorite, etc.

CSD discs are available on standard clamping shanks or with a central opening and are used on drills, flexible shafts and straight grinders. When coupled on a single shaft, they can be used as an aggressive brush. Typical uses include cleaning welds and contaminated metal surfaces, deburring and removal of oxides, rust, old paint deposits, etc. The effectiveness of cleaning is much higher than when using chemical strippers. Surfaces treated in this manner are much more resistant to subsequent oxidation. CSD discs relace wire brushes.

For coarse cleaning of metals, stripping of paint and conductive plates, etc. These high-performance, durable discs are primarily used on flat parts of workpieces. They are highly effective for mechanical cleaning and are a replacement for wire brushes. They are available either threaded on a metal backing or on a rubber/fibre backing.

A very hard and aggressive tool that is usable on stationary grinders, flexible shafts, straight grinders and drilling machines. Uses: removal of rust, old paint, oxides, burrs, paint deposits, insulating materials, gasket residue and welding spatter, cleaning of concrete casting moulds and general maintenance work. A very effective type of mechanical cleaning that replaces wire brushes.

A flexible system for changing abrasive tools for handheld grinders, robots and CNC machines.  Quick changes thanks to the special rotating fastener. You can use the Roloc+^TM system primarily for smaller high-speed grinders and hard-to-reach parts of surfaces and workpieces.

Scotch–Brite^TM flap brushes are made of individual segments that are anchored parallel to the axis on a fibre bushing. These brushes are available in various types of Scotch-Brite ^TM materials according to the aggressiveness and density of the segments and in various diameters and widths. They can be used immediately without any adjustment or difficult balancing on stationary grinders and buffing machines.

Scotch-Brite^TM brushes combined with emery cloth segments create a rougher appearance with greater depth of coarseness. The brushes remove lighter scratches and tool marks. They are ideal for deburring and cleaning surfaces.

These brushes are intended for various uses in the production of printed circuit boards. They deburr drilled holes, remove oxidation layers, clean and strip surface oxides before post-processing.

A shank is embedded in the core of these brushes. Modified in this way, the tool can be used on drills, flexible shafts, etc.

Buff brushes work more aggressively than buff brushes. They are suitable for working with contoured surfaces. They are used for deburring and buffing wooden workpieces and hot-melt adhesives on boards, finishing, cleaning, light deburring and edge rounding of metals, plastics, etc.

These discs provide versatile usage options on handheld grinders and stationary machines in working with metal and plastics. We supply these discs in various dimensions and grades of coarseness and density. They are used for deburring, precision machining of metal workpieces, obtaining decorative surfaces and final directional finishing, surface cleaning and reduction of surface roughness.

These discs are manufactured by moulding Scotch-Brite^TM material in a plane perpendicular to the axis of rotation. We supply them in a broad range of dimensions and grades of hardness. They are used for deburring, finishing and cleaning of metals and plastics. They can be used on stationary buffer machines and grinders. They are also available in smaller dimensions and can thus be used for cleaning, deburring and buffing very small products.

Scotch-Brite^TM belts are made of abrasive fleece with a cloth or plastic backing. They can be used on all belt sanders. Uses: deburring, finishing and cleaning of metals, high-grade steel and painted wood surfaces.

An advantage of these products is the repeatability of the coarseness of the material surface, thanks to precise orientation of the abrasive and the evenness of the plastic film backing. They are used for the finest sanding of metals, plastics, ceramic materials and hard metal, as well as for manual use on metal backings, files and special tools.

Used for fine sanding of metals, plastics, ceramic materials, hard metals and other materials, as well as primary use on superfinishing machines in the metalworking and plastics industries for achieving very fine reproducible profiles.

For working with flat parts of surfaces on all materials. Uses: on eccentric sanders, disc sanding machines and lapping machines. Areas of use: plastics, aircraft maintenance, metallurgy, maintenance and polishing of organic glass, metalworking industry, metallography, watchmaking and jewellery industry.

With these belts, you can achieve the smallest degree of surface roughness with consistently high quality. Uses: for finishing work in the metalworking industry, as well as for titanium, stainless steel, plastics, special coatings, etc.

Sanding and buffing system for rapid removal of defects and matte areas on acrylic glass, plexiglass, high-gloss lacquers, etc. Microabrasive materials are used for pre-sanding and for removing scratches and dust inclusions. Using the Finesse-it^TM microabrasive buffing emulsion, it is possible to achieve high gloss. Uses: on rotary and eccentric sanders and buffing machines.

These discs are used for machining very hard materials such as tungsten, ceramics and hard metals. The diamond particles are applied directly to the metal backing material. Flawless adherence of the diamond grains is guaranteed by the hard nickel coating. This involves very aggressive grinding.

The diamond particles are applied to the metal backing disc and are adhered with a synthetic resin. Areas of use: the finest grinding of samples prior to spectrometry in metallography, electronics, etc.

These abrasive discs are a special type of microabrasive materials modified according to the requirements of the optical industry. The discs are available with two types of abrasive. Areas of use: pre-grinding and fine grinding of plastic glass used in eyeglasses and polycarbonate contact lenses.

......

......